Mitel MiVOICE BUSINESS Engineering Manualline Download Page 326 | Manualshive

Page: 326 / 381

background image

Engineering Guidelines

312

Interface fa0/2 is connected to a MiVoice IP Phone that is capable of sending VLAN tagged
Ethernet frames. When learning the voice VLAN via CDP (as configured) an 802.1p value of
5 is initially assumed. However, if the Mitel proprietary DHCP option 133 is used then this will
overwrite the initial value. Mitel recommends an 802.1p value of 6 (unless using Cisco auto-qos).
By default 802.1p value 6 is a member of queue number 4. This is the expedited queue created
by the

priority-queue

out command on a Catalyst 3550. This interface configuration assumes

that DHCP option 133 is set to 6. If an alternate value (e.g. 5) is used then the queue members
need further defining. A local DHCP server or "IP helper" to a remote DHCP server is required
at the site.

ROUTER 1 CONFIGURATION

There are two physical interfaces on the Router 1 and an additional virtual interface.

•

S0/0 is the serial interface to the WAN. This could be an alternative technology but we show
PPP in this example.

•

Fa0/0 is the 10/100 physical Ethernet interface to Ethernet Switch 1 that connects to the
Data VLAN (i.e. VLAN 1).

•

Fa0/0.100 is the virtual interface that only "listens" to the Voice VLAN (i.e. VLAN 100).

An example configuration using static routes follows. If using dynamic routing protocols (RIPv2,
OSPF etc.) the static routes are not required.

Switch3(config)# interface fa0/24

[connection to Router 1 fa0/0]

Switch3(config-if)# description "Connection to Router 2
fa0/1 - Voice"

Switch3(config-if)# switchport trunk encapsulation dot1q

[Forces 802.1Q frame]

Switch3(config-if)# switchport mode trunk

[sends VLAN information across the link]

Switch3(config-if)# priority-queue out

[makes queue 4 a strict priority queue]

Interface fa0/24 is connected to the router.

«
...
324
325
326
327
328
...
»

Summary of Contents for MiVOICE BUSINESS






























































































































































































































































































































































































Reviews:

No comments

Related manuals for MiVOICE BUSINESS

Univerge SV8100

Brand: NEC Pages: 3

Brand: Samsung Pages: 78

Brand: Palm Pages: 52

Brand: Uniden Pages: 41

Sphere AAP553G-315

Brand: Bauhn Pages: 40

Brand: Sony Ericsson Pages: 75

Brand: Alcatel Pages: 2

Brand: Vonino Pages: 58

TALENT STATION TS-4

Brand: Wheatstone Pages: 33

Brand: ALIGATOR Pages: 20

Brand: Samsung Pages: 126

Brand: Samsung Pages: 119

Brand: Qubo Pages: 34

Brand: AMGOO Pages: 14

CLEARSOUND ClearText

Brand: Geemarc Pages: 31

VI 2300 - Sprint PCS Vision Phone

Brand: Sanyo Pages: 1

Brand: Sanyo Pages: 2

Brand: Sanyo Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands