Mitel MiVOICE BUSINESS Engineering Manualline Download Page 204 | Manualshive

Page: 204 / 381

background image

Engineering Guidelines

190

Other IP phones, however, do not support compression. Calls to and from these devices are
restricted to G.711 only. The following IP phones have this restriction:

•

4015 and 4025

•

5001 and 5005

•

5201, 5205, and 5207

3300 ICP controllers and compression

A single controller has the following limitations:

•

If the controller has one compression DSP module, the maximum number of compression
sessions is 32. If the controller has two compression DSP modules, the maximum number
of compression sessions is 64.

•

If the controller has DSP-II fitted, this is capable of up to 64 compression sessions per
module.

•

No more than 999 compression zones are possible from a single MiVoice Business/ICP
system.

•

E2T compression is used primarily to deal with TDM devices such as ONS phones or PSTN
connections.

•

At Release MCD 5.0, the 3300ICP can only terminate calls with G.711 or with G.729 com-
pression CODECs. Termination of G.722.1 connections is not provided, although the
3300ICP will handle through negation of the G.722.1 connection between end devices.

Internal 3300 ICP devices and compression

Conference

The conference feature is based on G.711 format, and is considered a TDM device.
Compression is needed in the 3300 ICP to communicate with each IP phone that normally uses
compression to a TDM device.

Voice Mail

Internal Voice Mail stores data in G.711 format, but compression can be used to and from this
device. An IP phone that uses compression to a TDM device uses compression to the voice mail.

Music On Hold

Music-on-Hold (MOH) can be sent with compression (at the expense of audio quality). Each
MOH session to an IP destination uses a compression license.

Note:

The dual DSP module used on the CX can support a maximum of 16 compression

sessions.

«
...
202
203
204
205
206
...
»

Summary of Contents for MiVOICE BUSINESS






























































































































































































































































































































































































Reviews:

No comments

Related manuals for MiVOICE BUSINESS

Brand: Pantech Pages: 101

Brand: Icemobile Pages: 59

Brand: Safeline Pages: 8

Brand: T-Mobile Pages: 4

Brand: i.safe MOBILE Pages: 21

Brand: Yealink Pages: 36

Brand: Doro Pages: 62

WeMove Discovery

Brand: NGM Pages: 11

Brand: ASCOM Pages: 112

Brand: Samsung Pages: 147

Brand: AEG Pages: 224

Brand: Haier Pages: 56

Brand: Haier Pages: 98

Brand: Aastra Pages: 134

Brand: Lava Pages: 59

Brand: G-Tide Pages: 24

Brand: Samsung Pages: 8

Brand: Samsung Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands