Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 92

Page: 92 / 366

Hardware

3.4.3 IP Phone Registration

Record the error message on the IP Phone display, then go through

Table 14: IP

Phone Registration Troubleshooting

on page 87 .

Note

IP sets require a firmware upgrade to support the new DHCP options introduced

in 3300 Release 7.0; otherwise, the sets will fail to boot. Such failures can occur,

for example, in a resilient cluster of mixed software releases or when sets with old

firmware are added to a controller after it was upgraded to Release 7.0. For the

sets to boot, DHCP options 128-133 must be present in the DHCP server. After the

sets have booted, options 128-133 may be removed to avoid future conflicts with

standardized or other vendors’ use of these options.

If you still can’t fix the problem collect the following information and then call Mitel

Technical Support:

•

Is the problem with the local or remote subnet?

•

DHCP server(s) settings

•

Layer 2 switch configuration and settings

•

Router configuration and settings

•

Network Diagram

•

IP addressing scheme

•

VLAN configuration and settings

Document Version 1.0
Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands