manualshive.com logo in svg

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Share
Download
Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 312

Diagnosing Problems

Table 58: IP Phone Error Handling Displays

Message Description

Phone Display

Note

:

Check the IP Parameters (TFTP address, netmask, gateway address), to make

sure that they are valid, before calling Mitel.

If TFTP fails, usually due to incorrect

TFTP Server or Gateway IP address,

review IP parameters and correct errors.

RTCS creat err <number>

BOOTING xx.xx.xx.xx

-------------------------

If add err <number>

BOOTING xx.xx.xx.x

-------------------------

RTCS Bind err <number>

BOOTING xx.xx.xx.x

The TFTP server sent an “I am busy” error

so the phone will delay and retry.

xx.xx.xx.xx

Waiting for TFTP

If the phone received a bad packet from

the TFTP server, audit the TFTP server

configuration and the network path.

xx.xx.xx.xx

TFTP Err: <number>

This error indicates that you must review

the IP parameters on the DHCP server or

manually entered for the phone.

xx.xx.xx.xx

TFTPerr: Packet send

Document Version 1.0
Troubleshooting Guide

306

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands