Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 196

Page: 196 / 366

Trunking

6.5 IP Trunking (IP Networking)

Table 31: IP Trunk Troubleshooting

Symptom

Possible Cause

Corrective Action

IP trunk does not

recover after router

crash.

ICMP redirect is

enabled.

On the Linux shell, enter the

following command to find the

redirected route entry:

root@mxeiii:~# route -n

Kernel IP routing table is

displayed.

If you want to delete route

Destination

<IP address>

enter the following table:

root@mxeiii:~# route

del -net <Destination

IP address> netmask

<Genmask IP address> gw

For a permanent solution:

•

Make sure that the route has

a “permanent” static route to

the remote IP trunk network.

•

Turn IP redirect off.

•

Turn on the routing protocol

between local router and

ISP router.

Unable to place calls

between systems via

IP trunks in a clustered,

redirected, or resilient

environment.

ARS Routes or PBX

Number in the ICP/

PBX Assignment forms

of the systems are

programmed incorrectly.

For each system in the cluster,

ensure that the system’s PBX

Number matches its CEID Index

Number as defined in the Cluster

Elements form.

Document Version 1.0
Troubleshooting Guide

190

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands