Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 174

Page: 174 / 366

Trunking

6.2 Digital Trunks

Table 28: Digital Trunk Troubleshooting

Symptom

Probable Cause

Corrective Action

General

Excessive Bit Error

Rate.

Faulty programming.

Make sure the system is

programmed the same as the CO,

for B8Zs or AMI.

Excessive Slips.

Faulty programming.

Ensure the Network

Synchronization form is

programmed and the system is

clocking appropriately. Use the

Netsync Summary maintenance

commands to determine if

synchronization is taking place,

If not, use Net Set 1 to set off the

first clock source or NET SET

AUTO to select the best available

clock source. After you choose

a synchronization clock source

always use the NET SET AUTO

command to confirm.

System is not

Receiving Calls.

The DID trunk digit

modification number

on the Trunk Attributes

form does not have

anything programmed

in the absorb field.

It MUST have a

minimum of 0, or no

calls will be accepted.

Ensure that there is an entry in the

absorb field. It cannot be left Blank.

Document Version 1.0
Troubleshooting Guide

168

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands