Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 120

Page: 120 / 366

Software

Symptom

Possible Cause

Corrective Action

(Hyper-V)

Unable to

access the

MiVoice

Business

System

Administration

Tool through

web browser or

SSH.

MAC address of the

virtual machine has

changed.

If power is restored to a virtual machine

(Hyper-V) after a prolonged power loss,

Hyper-V dynamically assigns a new

MAC address to the virtual machine.

This prevents access to the System

Administration Tool. To resolve the issue:

Access the system through SSH using

a communication application, such as

PuTTy.

root

Run the

ip a

command to determine

the current MAC address.

Backup the virtual machine.

Power down the virtual machine.

In the Hyper-V Manager, select the

virtual machine and click Settings.

In the left pane, expand Network

Adapter, and click Advanced Features.

In the right pane, under MAC Address,

select Static and enter the current MAC

address.

Click OK.

10.

Power on the virtual machine.

4.2 Unable to Perform Full Manual Installation of an ICP3300

Controller

Overview

The manual software installation of an ICP3300 Controller fails with error code 22

because the HTTP server returns a

400 Bad Request

. This

400 Bad Request

response

code indicates that the server is unable to process the request due to a client error (for

example: incorrect request syntax, invalid request message framing, or misleading

request routing).

Document Version 1.0
Troubleshooting Guide

114

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands