manualshive.com logo in svg

Mitel Inter-Tel Axxess, Administrator'S Manual, Page: 340 / 384

Share
Download
Mitel Inter-Tel Axxess Administrator'S Manual Download Page 340

Page  324

Voice Processing Prompts

Inter-Tel

® 

Axxess

® 

Administrator Guide — Issue 11.0, May 2008

Voice Processing Systems

VOICE PROCESSING SYSTEMS

This section contains all of the default voice prompts for the three voice processing systems
supported by the Axxess Converged Communications Platform. The Axxess platform supports
the following voice processing systems:

•

Voice Processing Unit: 

The Voice Processing Unit (VPU) runs on either the Windows

NT or Windows 2000 operating systems. The VPU system is installed on an IBM-com-
patible PC that is connected to the Inter-Tel system to provide integrated voice process-
ing features such as Voice Mail, Directories, Record-A-Call, etc.

•

Embedded Voice Mail Card:

 The Embedded Voice Mail Card (EVMC) runs on the

OS/2 or the Linux operating system. The EVMC provides voice processing for small to
medium-sized systems. It can support 32, 64, or 200 mailboxes, depending on the con-
figuration. The EVMC’s 2.0 Gigabyte hard drive will support up to 180 hours of voice
messages. The EVMC supports AMIS networking and database saves to a zip or floppy
drive. It does not support Fax-On-Demand and Unified Messaging.

•

Enterprise

®

 Messaging:

 Enterprise Messaging (EM) runs on the Windows 2000 oper-

ating system. EM is an external voice processing system. EM unifies communication
and messaging by providing access to voice mail, fax, and e-mail messages in the user’s
mailbox. In addition, EM provides automatic speech recognition capabilities and built-
in Unified Messaging features. EM supports Voice Profile for Internet Mail (VPIM)
networking. For detailed information about EM, see the 

Enterprise Messaging Installa-

tion and Maintenance Manual

 (part no. 780.8006). 

AUTOMATIC SPEECH RECOGNITION (ASR)

The Enterprise Messaging (EM) voice processing system supports Automatic Speech Recogni-
tion (ASR), which allows users to access voice mail, call routing applications, the automated
attendant and the directories by issuing spoken commands instead of dialing digits on their
endpoint. If ASR is enabled on a voice processing system, users are prompted to speak or press
a digit on the dialpad to complete a voice mail task. If ASR is not enabled, users are only
prompted to press a digit. ASR is currently supported on EM voice processing systems only.

DEFAULT ASR AND NON-ASR VOICE PROMPTS

The following table shows all of the U.S. English default system voice prompts for ASR- and
non ASR-enabled systems. Prompts designated by an asterisk (*) cannot be re-recorded.  

Table 37. 

Voice Prompts: Non-ASR and ASR 

PROMPT 

ID

CONTENT (NON-ASR) 

CONTENT (ASR)

001

To leave a message, please enter a mailbox 
number.

To leave a message, please say or enter a mail-
box number.

002

For the directory, press pound (or hash in Euro-
pean systems).

For the directory, say “Directory” or press pound 
(or hash).

003

To reach an operator, press zero.

To reach an operator, say “Operator” or press 
zero.

004

I’m sorry...

N/A

005

...is not available.

N/A

006

The number entered is not valid.

N/A

Summary of Contents for Inter-Tel Axxess

































































































































































































































































































































































































Reviews:

No comments