manualshive.com logo in svg

Mitel DBC 223, Directions For Use Manual, Page: 93 / 121

Share
Download
Mitel DBC 223 Directions For Use Manual Download Page 93

M

I

V

OICE

 4223 O

FFICE

 (DBC 223) 

FOR

 M

I

V

OICE

 MX-ONE

93

3/1553-ANF 901 54 Uen F5 2018-12-03

9.12 

LEAST COST ROUTING

9.12.1 

GENERAL

The Least Cost Routing Facility can be accessed by dialing Least Cost Routing Access 

Code (LAC).
By using Least Cost Routing Access Code you will automatically be routed over the 

cheapest available route. You cannot choose the cheapest route yourself, this is 

performed automatically by LCR.

9.12.2 

PROCEDURE

9.12.2.1 

Outgoing call by using LAC

•

Lift hand set

•

Dial LAC provided a dial tone is received.

•

Continue with the external number. If no free trunk is selected, a busy tone is 

received. On-hook queuing is possible by dialing the suffix digit for call-back to 

the busy route. If the selected route is marked as expensive, you will receive 

Expensive Route Warning Tone which will make it possible for you to interrupt 

the further routing of the call.

•

Replace the handset when the call is completed.

9.13 

MALICIOUS CALL TRACING, MCT

This feature allows you, before the call is disconnected, to signal to the public switched 

telephone network (PSTN) that you have received a 

malicious

  call. If the calling 

subscriber clears the call, the external line can be held for a limited period of time, 

during which you can invoke the feature. This information is used by the PSTN to 

record information about the origin of the call (that is, print calling party number, date, 

time, and so on).
The following is the procedure for invoking malicious call tracing while connected to a 

subscriber:

9.13.1 

TO ORDER MALICIOUS CALL TRACING

•

Press the soft-key 

TraceMalC

  or the MCT-key.

The system acknowledges with a tone message indicating if the MCT request was 

accepted or rejected.

9.14 

MULTIPLE REPRESENTED DIRECTORY NUMBER, MDN

The directory number assigned to the telephone can be multiple represented in other 

digital system telephones. That is, the directory number is represented as a key on 

other digital system telephones.
This key can also be assigned a Dial-by-Function key, in order to get the best use of 

the keys on the telephone.

Summary of Contents for DBC 223


























































































































Reviews:

No comments