Mitel DBC 223 Directions For Use Manual Download Page 85

Page: 85 / 121

OICE

4223 O

FFICE

(DBC 223)

FOR

OICE

MX-ONE

3/1553-ANF 901 54 Uen F5 2018-12-03

9.2

ADDITIONAL DIRECTORY NUMBER, ADN

You can be assigned one or more additional directory numbers. These are

programmed on free function keys on your telephone. When using the additional line,

use the following procedures:

9.2.1

TO RECEIVE A CALL

Incoming call to an additional line-key is indicated by a flashing lamp (the additional

line-key's lamp) and a ringing signal is heard.
•

Lift the handset (dial tone).

•

Press the additional line-key.

9.2.2

TO RECEIVE A CALL IN HANDSFREE MODE

•

Press the additional line-key.

9.2.3

TO TERMINATE THE CALL

•

Press the Clear-key or replace the handset.

9.2.4

TO MAKE A CALL

•

Lift the handset (dial tone).

•

Press the additional line-key (dial tone).

•

Dial the wanted number.

9.2.5

USING FEATURES FROM AN ADDITIONAL LINE

Features have the same procedure as for triple access line if nothing else is stated with

the exception that the additional line-key has to be pressed after lifting the handset.

9.2.6

MULTIPLE DIRECTORY DIVERSION AND DND

This facility allows you to order and cancel the following features for all ADNs on the

telephone, without doing the procedure for each ADN:
•

When follow-me, direct diversion or message diversion is ordered or canceled

from the ODN, the diversion is also ordered or canceled for all ADNs assigned

to your extension. The same rules are applied as if the procedure to order or

cancel the diversion had been dialed from the ODN and each ADN on the exten

sion.

•

When DND is ordered or canceled from the ODN, DND is also ordered or

canceled for all ADNs assigned to your extension. The same rules are applied

as if the procedure to order or cancel DND had been dialed from the ODN and

each ADN on the extension.

•

When general cancellation is ordered from the ODN, the features follow-me,

direct diversion, message diversion and DND initiated for the ADNs are also

canceled.

This facility is controlled by a category (programmed by the system administrator).

Summary of Contents for DBC 223


























































































































Search results

Summary of Contents for DBC 223

Reviews:

Mitel DBC 223, Directions For Use Manual, Page: 85 / 121

Search results

Summary of Contents for DBC 223

Reviews: