manualshive.com logo in svg

Mitel DBC 223, Directions For Use Manual, Page: 53 / 121

Share
Download
Mitel DBC 223 Directions For Use Manual Download Page 53

M

I

V

OICE

 4223 O

FFICE

 (DBC 223) 

FOR

 M

I

V

OICE

 MX-ONE

53

3/1553-ANF 901 54 Uen F5 2018-12-03

4.8.1 

COMMON SPEED DIALING NUMBERS

External telephone numbers that are of importance, and frequently used by everybody 

in the company are provided directly by the exchange. These speed dialing numbers 

consist of 1-5 digits.

To use

•

Lift the handset (dial tone).

•

Dial the abbreviated number.

4.8.2 

INDIVIDUAL SPEED DIALING NUMBERS

Up to ten of your most important and frequently needed telephone numbers can be 

programmed on your telephone as individual abbreviated numbers from 0-9, 10 

Settings on page 99  for programming.

To use

•

Lift the handset (dial tone).

•

Dial **Digit.

4.8.3 

DIAL-BY-FUNCTION KEY

Any function key can be programmed with a telephone number and labelled with a 

name. This means that when you press that function key the desired telephone number 

is automatically dialled, 10 Settings on page 99  for programming.

To use

•

Lift the handset (dial tone).

•

Press the Dial-by-Function key.

Summary of Contents for DBC 223


























































































































Reviews:

No comments