manualshive.com logo in svg

Mitel DBC 223, Directions For Use Manual, Page: 24 / 121

Share
Download
Mitel DBC 223 Directions For Use Manual Download Page 24

3/1553-ANF 901 54 Uen F5 2018-12-03

24

I

NCOMING

 

CALLS

Note:  

For an additional line, the DND lamp is not affected

Using the soft-key CancelDND

•

Press the soft-key 

CancelDND

  (the diversion lamp is turned OFF).

3.5 

IMMEDIATE SPEECH CONNECTION

With this feature a call is signaled with a tone burst after which the call is answered 

automatically (you get a speech connection) in handsfree mode ( 2.8 Loudspeaker 

function on page 18 ).
This feature can be permanently active or activated by means of a specially 

programmed automatic answer key.

3.5.1 

PERMANENTLY ACTIVE

For the feature to be permanently active program the ring option with permanent imme

-

diate connection with single tone burst on the line-key ( 10.8 To program ringing 

options on page 103 ).

3.5.2 

ACTIVATED BY AUTOMATIC ANSWER-KEY

First you have to program the ring option with immediate speech connection with single 

tone burst controlled by function key on the line-key ( 10.8 To program ringing options 

on page 103 ). Now you can control the automatic answer with the function key AUTO

-

MATIC ANSWER. When the lamp lights up, the calls will be answered automatically.

To order

•

Press the Automatic answer-key (the automatic answer lamp is turned ON).

Summary of Contents for DBC 223


























































































































Reviews:

No comments