Mircom FR-320 Series Installation And Operation Manual Download Page 73

Page: 73 / 112

Pre-Programmed Modes

12.3

Mode 3: Agent Release, Dual Hazard, Cross-zoned, Split
Release

12.3.1 Zone Configuration

•

Detection Zone -1: Alarm (Hazard Area 1, Cross-zoned)

•

Detection Zone -2: Alarm (Hazard Area 1, Cross-zoned)

•

Detection Zone -3: Alarm (Hazard Area 2, Cross-zoned)

•

Detection Zone -4: Alarm (Hazard Area 2, Cross-zoned)

•

Detection Zone -5: Abort/Manual Release Combination (Hazard Area 1)

•

Detection Zone -6: Abort/Manual Release Combination (Hazard Area 2)

•

NAC -1: Escalating Signal, indicates Hazard Area 1 state

•

NAC -2: Escalating Signal, indicates Hazard Area 2 state

•

RAC -1: Releasing Circuit (Hazard Area 1)

•

RAC -2: Releasing Circuit (Hazard Area 2)

12.3.2 Hazard Configuration

•

Default Release Timer Value: 60 seconds

•

Default Manual Release Delay: 0 seconds.

•

Default Abort Delay Type: Standard UL.

•

Default Soak Timer Value: 0 seconds

12.3.3 NAC Configuration

•

Default Escalating NAC code of Hazard Area State:

•

Hazard Idle: Off

•

Hazard Alert: Temporal (see Table 7)

Detection Zones

Phantom Zones

Release Timers

Zp1

Zp2

RT1

Exp

RT2
Exp

Alm

AB/MR

Z1+Z2

Z3+Z4

Out1

Signal

Steady

Out2

Signal

Escalating

Out3

Rel.

Releasing

Out4

Rel.

Releasing

RLS TMR 1 Started

RLS Tmr 1 Interrupted

RLS Tmr 1 Cancelled

RLS Tmr 2 Started

RLS Tmr 2 Interrupted

RLS Tmr 2 Cancelled

Note:

Dual hazard operation is not permissible for UL/ULC operation.

Summary of Contents for FR-320 Series

















































































































Search results

Summary of Contents for FR-320 Series

Reviews:

Related manuals for FR-320 Series

Brands by name

Popular brands

Mircom FR-320 Series, Installation And Operation Manual

Search results

Summary of Contents for FR-320 Series

Reviews:

Related manuals for FR-320 Series

Brands by name

Popular brands