manualshive.com logo in svg

Mipex MIPEX-02 Series, User Manual, Page: 33 / 46

Share
Download
Mipex MIPEX-02 Series User Manual Download Page 33

 

Optosense LLC 

USER MANUAL 

Design department 

SMALL-SIZE EXPLOSIVE GAS MEASURING 

SENSOR MIPEX-02-X-X-X.1 X (RX) 

 

ESAT.413347.005 UM 

Revision 3.0 

January 19th, 2017 

Page 33 of 46 

THE SOLE PROPERTY OF OPTOSENSE LLC. ANY REPRODUCTION WITHOUT THE WRITTEN PERMISSION OF OPTOSENSE LLC IS PROHIBITED. 

 

Table 12. Bits of status bytes description 

Bit number of 

<DATAE2> 

status-bytes 

Bit number of 

<DATAE> 

status-byte 

Status word 

compliance

11

 

Description 

Recommendations 

– 

– 

00 

Normal mode, static temperature 

– 

0 

0 

10 

Sensor is warming up. 

Do not perform span calibration. 

1 

1 

50 

An  abrupt signal  change  (due  to 
feeding  a  gas  mixture  to  sensor 
atmosphere)  or  increased  noise 
on sensor optical elements. 

Do  not  perform  span  calibration  or 
zeroing.  If  this  status  longer  than  for 
20  minutes  at  stable  conditions, 
replace sensor. 

2 

2 

30 

One of the signal values is lower 
than it is allowed. 

Possibility  of  condensed  moisture  on 
optical  elements.  Dry  sensor.  After 
drying,  if  this  status  lasts  longer  than 
for  20  minutes  at  stable  conditions, 
replace sensor. 

3 

3 

– 

reserved 

Does  not  contain  any  significant 
information. 

4 

4 

21 

Dynamic 

temperature 

mode 

(temperature 

changes 

faster 

than by 0.6 °C/min). 

Do  not  perform  span  calibration  or 
zeroing. 

5 

5 

22 

Dynamic 

temperature 

mode 

(temperature 

changes 

faster 

than by 2 °C/min). 

Do  not  perform  span  calibration  or 
zeroing. 

6 

6 

40 

Exceeding temperature limits. 

Check the ambient temperature. 

7 

7 

90 

Firmware  failure  (flash  memory 
issues). 

Contact support for details. 

8 

– 

11 

Data request rate is more than 1 
Hz. 

Do  not  perform  span  calibration  or 
zeroing. Decrease request rate. 

9 

– 

31 

Zero shifts to negative value. 

Possibility  of  condensed  moisture  on 
optical  elements.  Dry  sensor.  After 
drying,  if  this  status  lasts  longer  than 
for  20  minutes  at  stable  conditions, 
perform zeroing (see Appendix D.1 for 
procedure description). 

10 

– 

1XX 

Sensor  operates  in  low  power 
consumption mode. 

– 

11 

– 

51 

Complex  status.  Technological 
failure. 

Contact support for details. 

12 

– 

– 

reserved 

Does  not  contain  any  significant 
information. 

13 

– 

– 

reserved 

Does  not  contain  any  significant 
information. 

14 

– 

– 

reserved 

Does  not  contain  any  significant 
information. 

15 

– 

– 

reserved 

Does  not  contain  any  significant 
information. 

(4 

∨ 

5) & 9 

– 

24 

Dynamic 

temperature 

mode; 

zero shifts to negative value. 

Do  not  perform  span  calibration  or 
zeroing. 

                                                

11

 Status word is contained in response to command <F> (see Table 17). 

Summary of Contents for MIPEX-02 Series















































Reviews:

No comments