MINOURA RDA Inter-Rim Ergo-10 Manual Download Page 1

- 1 -

(This figure is the Remote Control version)

MINOURA RDA Inter-Rim Ergo-10 / 50 Instruction manual

Please read this instructions carefully before use

• Read all instructions carefully before use.

• Some assembly required.

• Keep the manual handy at all times.  Lost instruction materials can be replaced through

Minoura or your local dealer.

• Do NOT use trainer for any other purpose than instructed.

• The trainer is manufactured to precise standards.  You may not disassemble or re-

build it.

• "Inter-Rim" and "RDA" are trademarks of Minoura and may not be copied.

Thank you for purchasing Minoura's Inter-Rim Ergo Trainer with RDA and Magturbo.

With its unique rim-drive system, the RDA Inter-Rim Magturbo is our most sophisticated bicycle home

trainer for both road and mountain bikes.  Minoura has long been an innovator in stationary trainers, and

our new Inter-Rim trainer continues that tradition.  The Rim Drive Action (RDA) system has special drive

pulleys that contact only the rim, avoiding wear and tear to the tire and any unpleasant noise.  With the

RDA system, training is smoother, more adjustable, and quieter, and you avoid the cost of replacing worn-

down tires.  The RDA system can handle almost any bicycle with a wheel diameter of 26 to 28 inches and

is the best trainer yet for mountain bikes.

Summary of Contents for RDA Inter-Rim Ergo-10













Reviews: