manualshive.com logo in svg

Minolta CF1501, Service Manual

Share
Download
Minolta CF1501 Service Manual Download Page 47

FrameMaker Ver5.5E(PC) CF1501/CF2001 MECHANICAL/ELECTRICAL
00.12.15

M-32

11. ORIGINAL SIZE DETECTING SECTION

• Original Size Detecting Sensors are provided for detecting the size of the original.

11-1.

Original Size Detecting Method

• The Original Size Detecting Sensors work on a principle that the intensity of light 

reflected off the original varies with different distances.

• Light emitted by the LED of each sensor is reflected off the surface of the original.  When 

the photoreceiver of the sensor receives light of a given intensity level or higher, the 
copier then determines that there is an original on the Original Glass.

1. Original Cover Detecting Sensor (PC25)
2. Original Size Detecting Sensor FD1 

(PC30)

3. Original Size Detecting Sensor FD2 

(PC31)

4. Original Size Detecting Sensor FD3* 

(PC33)

5. Size Reset Switch (SW10)
6. Original Size Detecting Sensor CD2* 

(PC34)

7. Original Size Detecting Sensor CD1 

(PC32)

*: Optional

4004M519AA

1

2

3

4

5

6

7

Front

Rear

4002M522AA

Original Size 
Detecting Sensor

LED

Photoreceiver

Original

Original Glass

Summary of Contents for CF1501















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands