manualshive.com logo in svg

MINOLTA-QMS MAGICOLOR 6110, User Manual

Share
Download
MINOLTA-QMS MAGICOLOR 6110 User Manual Download Page 169

Remove the Cables and Media Tray(s) 

167

Remove the Cables and Media Tray(s)

1

Turn off the printer.

2

Remove the power cable and all interface cables.

3

Remove the media tray(s) from the printer.

Remove the Toner Cartridges 

1

Open the printer’s front and top covers.

Attention

If you have an optional duplex unit installed, always open the duplex 
unit’s top cover before opening the printer’s top cover.

Leave the covers open during the repacking procedure.

2

Remove the four toner cartridges, attach the protective shields over their 
magnetic rollers, and store them in their original packaging.

Prepare the Fuser Unit 

WARNING!

The fuser unit can become extremely hot and cause severe 
burns. Make sure the unit is cool before handling it.

ACHTUNG! Die Fixiereneinheit kann sehr heiß werden, so daß 
Verbrennungsgefahr besteht. Bitte lassen Sie die Fixiereneinheit einige 
Zeit abkühlen, bevor Sie diese berühren.

1

With the printer’s top 
cover open, at the 
top of the fuser, 
rotate the two lock 
levers to release the 
oil bottle. 

Summary of Contents for MAGICOLOR 6110

























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands