manualshive.com logo in svg

MINOLTA-QMS magicolor 330, Service Manual

Share
Download
MINOLTA-QMS magicolor 330 Service Manual Download Page 43

magicolor 330 Large-Capacity Input Feeder Service Manual

LCIF-39

5.2

Printer Error: Prints Damaged When Fed From the LCIF

Paper Fed from the LCIF exits the printer either wrinkled, creased, or torn. The printer neither jams nor displays
an error message.

Step

Actions and Questions

Yes

No

SUSPECT COMPONENTS
The following components are associated with this specific
problem. One or more of these components may have failed
partially or completely. If you cannot isolate the problem using
this FIP, replace each component listed below, one at a time,
until the problem disappears.

• Wiring and connectors linking the components

1

FEEDER ISOLATIO

Feed paper out of OPT1 Tray, then OPT2 Tray, and then OPT3
Tray.

Is the paper damaged when fed out of OPT1 Tray?

Go to step 4

Go to step 2

2

Is the paper damaged when fed out of OPT2 Tray?

Go to step 4

Go to step 3

3

Is the paper damaged when fed out of OPT3 Tray?

Go to step 4

4

PAPER INSPECTION

Inspect the paper that is loaded in the suspect tray.

Is the paper in good condition and undamaged?

Go to step 5

Replace the 
paper with 
new, undam-
aged paper

5

PAPER TRAY INSPECTION

Remove and inspect the suspect paper tray.

Is the paper tray in good condition and undamaged?

Go to step 6

Replace the 
paper tray 
with a new 
one

6

FEEDER INSPECTION
Feed a sheet of paper out of the suspect paper tray and open
the  LCIF  Cover  Assembly  just  after  the  leading  edge of the
paper exits the tray’s Drive Assembly.

Is the sheet of paper damaged as it exits the Drive Assem-
bly?

Go to step 7

Go to step 8

7

1. Replace the Feed Rolls in the suspect Feeder LCIF DRP

6.18).

2. Feed a sheet of paper out of the suspect paper tray and

open the LCIF Cover Assembly just after the leading edge
of the paper exits the tray’s Drive Assembly.

Is the sheet of paper damaged as it exits the Drive Assem-
bly?

Replace the 
LCIF Drive 
Assembly 
(LCIF DRP 
6.15)

Problem 
solved

Summary of Contents for magicolor 330





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands