manualshive.com logo in svg

MINOLTA-QMS MAGICOLOR 2210, User Manual

Share
Download
MINOLTA-QMS MAGICOLOR 2210 User Manual Download Page 95

Status, Error, and Service Messages 

93

WAITING ON 

INPUT

END JOB?

The compiler is waiting on 
incoming data for the first job in 
the queue. The job may not 
have an end-of-job indicator 
and therefore cannot end. The 
message clears if more input 
arrives from the port or if you 
press the Cancel key. No other 
jobs can be printed until this 
job has ended.

Wait until the job is 
finished and the 
printer goes idle to 
access the config-
uration menu.

WARMING UP

The printer is warming up. 

Wait. No other 
action needed.

WASTE TONER 

NEAR FULL

The waste toner pack is nearly 
filled with toner.

Replace the waste 
toner pack.

WASTE TONER 

FULL

The waste toner pack is filled 
with toner.

Replace the waste 
toner pack.

This message...

means...

Do this...

Summary of Contents for MAGICOLOR 2210

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands