manualshive.com logo in svg

MINOLTA-QMS MAGICOLOR 2210, User Manual

Share
Download
MINOLTA-QMS MAGICOLOR 2210 User Manual Download Page 94

Status, Error, and Service Messages

92

OUTPUT BIN 

FULL

The media has exceeded the 
limit in the specified output bin.

Remove the media 
from the specified 
output bin.

PAPER MIS-

MATCH

The media detected in the tray 
doesn’t match the media size 
setting.

Change the media 
in the tray or 
change the media 
size setting. 

PRINTING STA-

TUS

A status page is printing

Wait until after the 
status page prints, 
and the message 
clears.

PUT <

X> IN 

INPUT <

Y>

The 

<

X>

 specified media is not 

in the input tray 

<

Y>

.

Refill the tray with 
the specified type 
media. 

PUT <

SIZE> 

PAPER IN 

<

BIN> 

The Operator Control/Chain 
Inputbins is set to Off and the 
displayed tray is empty. Refill it 
with the specified size media. 
<

SIZE>

 is the media size 

detected by the engine, and 
<

BIN>

 is the empty tray.

Refill the tray with 
the specified size 
media.

PUT <

TYPE 

MEDIA> IN 

INPUT BIN

Operator Control/Chain Input-
bins is set to On and a chained 
tray is empty. 

Refill the tray with 
the specified type 
media. 

REPLACE <

X>

The specified item 

<

X>

 needs 

to be replaced, such as the 
OPC drum.

Replace the speci-
fied item.

RESETTING 

ACCOUNTING

The reset accounting operation 
is in process.

No action needed.

WAITING FOR 

IDLE

An active job is in process. 
Access to the menu is not 
allowed until the job is finished.

Wait until the print 
job is finished and 
the printer goes 
idle.

This message...

means...

Do this...

Summary of Contents for MAGICOLOR 2210

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands