manualshive.com logo in svg

MINOLTA-QMS MAGICOLOR 2210, User Manual

Share
Download
MINOLTA-QMS MAGICOLOR 2210 User Manual Download Page 71

Solving Other Problems 

69

Solving Other Problems 

Symptom

Cause

Solution

Printer 
power is 
not on.

The power cord is 
not correctly 
plugged into the 
outlet.

Turn the power switch off (O position), 
then remove the power cord from the 
outlet and plug it back in.

The mailbox power 
cord is not correctly 
connected.

Turn the power switch and the mailbox 
power switch off (O position), then 
reconnect the mailbox power cord using 
the procedure below:
—Connect the mailbox power cord plug 
end to the mailbox power socket (lower 
connection).
—Connect the mailbox power cord 
socket end to the printer power plug.
—Connect the printer power cord 
socket end to the mailbox power plug 
(upper connection).
—Plug the printer power cord into the 
outlet.

Something is 
wrong with the out-
let you are using 
for the printer.

Plug another electrical appliance into 
the outlet and see whether it operates 
properly.

The power switch 
is not correctly 
set to the On (I) 
position.

Set the power switch to the Off (O) 
position, then set it back to the On (I) 
position. 

Turn the printer power switch and the 
mailbox power switch to the Off (O) 
position, then turn on the power again 
using the procedure below:
—Turn the mailbox power switch on.
—Turn the printer power switch on. 

Something is 
wrong with the out-
let you are using 
for the printer.

Plug another electrical appliance into 
the outlet and see whether it operates 
properly.

Summary of Contents for MAGICOLOR 2210

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands