manualshive.com logo in svg

MINOLTA-QMS MAGICOLOR 2210, User Manual

Share
Download
MINOLTA-QMS MAGICOLOR 2210 User Manual Download Page 70

Solving Problems with Media Jams

68

Media is 
jamming.

Labels, letterhead, 
envelopes, post-
cards, thick stock, 
or transfer material 
are loaded in the 
upper or optional 
tray.

Special media must be loaded in the 
multipurpose tray only.

The recommended 
transparency 
(OHP) or label 
paper is facing the 
wrong way in the 
multipurpose tray.

Load the transparencies or labels 
according to the manufacturer’s 
instructions.

Envelopes are fac-
ing the wrong way 
in the multipur-
pose tray.

Load the envelopes in the multipurpose 
tray so the the flaps are facing up. 

If the flaps are on the short edge, set 
the envelopes in the multipurpose tray 
so that the flaps are on the printer side. 

Multiple sheets of 
transparency 
(OHP) media are 
collecting static 
electricity in the 
tray.

Remove the OHP media and load them 
in the tray one sheet at a time. Do not 
fan transparencies before loading them. 

The media is moist 
from humidity.

Remove the moist media and replace it 
with new, dry media. 

Unsupported 
media (wrong size, 
thickness, type, 
etc.) is being used.

Use media that is covered by the printer 
warranty.

Media supply roller 
is dirty.

Clean the media supply roller.

Symptom

Cause

Solution

Summary of Contents for MAGICOLOR 2210

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands