manualshive.com logo in svg

MINOLTA-QMS MAGICOLOR 2210, User Manual

Share
Download
MINOLTA-QMS MAGICOLOR 2210 User Manual Download Page 60

Clearing Media Jams

58

Clearing Misfeed (Multipurpose Tray) Jams

1

Remove the media from in the multipurpose tray.

2

Carefully remove the jammed media.

3

Shuffle the media that was removed in 
step 1 and even up the front edges.

4

Reinsert the media printing face down.

Make sure the media is lying flat and doesn’t 
exceed the media limit mark. Check to see if 
the media width guides are correct.

5

Open the front cover, then close it.

The media jam message is no longer displayed in the printer message 
window.

Clearing Inner Jams, Outer Jams, and Drum Jams

 

 

Media Jams inside the Lower Right Door (Vertical 
Transport Area) 

1

Open the lower right door(s).

2

Carefully remove the jammed 
media.

3

Close the lower right door(s).

The media jam message is no 
longer displayed in the printer 
message window.

Summary of Contents for MAGICOLOR 2210

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands