MINOLTA-QMS MAGICOLOR 2210 User Manual Download Page 54

Page: 54 / 176

Introduction

Introduction

This chapter provides information to aid you in resolving printer problems you
may encounter, or at least guide you to the proper sources for help.

Printing a Status Page

Print a status page to verify the printer is printing correctly.

Preventing Media Jams

Press Key

(Until) Display Reads

Online

IDLE

(and online LED is off)

OPERATOR CONTROL

Next (

)

ADMINISTRATION

Select

ADMINISTRATION–SPECIAL PAGES

Select

PRINT STATUS

Select

YES

Online

IDLE

(and online LED is on)

Make sure that...

Avoid...

Media matches the printer specifi-
cations

Media that is folded, wrinkled, or
excessively curled

Media is flat, especially on the lead-
ing edge

Double feeding (remove the media
and fan the sheets—they may be
sticking together)

The printer is on a hard, flat, level
surface

Fanning transparencies since this
causes static

You have the correct media type
selected if you’re printing on enve-
lopes, labels, thick stock, or trans-
parencies.

Loading more than one type/size/
weight of media in a tray at the
same time

You store media in a dry location
away from moisture and humidity

Overfilling the media input trays

Summary of Contents for MAGICOLOR 2210

















































































































































































Search results

Summary of Contents for MAGICOLOR 2210

Reviews:

Brands by name

Popular brands

MINOLTA-QMS MAGICOLOR 2210, User Manual

Search results

Summary of Contents for MAGICOLOR 2210

Reviews:

Brands by name

Popular brands