manualshive.com logo in svg

MINOLTA-QMS MAGICOLOR 2210, User Manual

Share
Download
MINOLTA-QMS MAGICOLOR 2210 User Manual Download Page 51

Maintaining the Printer 

49

„

Do not put a cover on the printer immediately after using it. Turn it off and 
wait until it cools down.

„

Do not leave the printer’s covers open for any length of time, especially in 
well-lit places; light may damage the OPC drum cartridge.

„

Do not open the printer during printing.

„

Do not tap paper stacks on the printer.

„

Do not tilt, lubricate, or disassemble the printer.

„

Do not touch the electrical contacts, gears, or laser beam devices. Doing 
so may damage the printer and cause the print quality to deteriorate.

„

Keep media in the output tray at minimum level. If the media stacks too 
high, your printer may experience media jams and excessive media curl.

„

Lift the printer from the bottom only, using the carrying grips and the 
carrying bars. Make sure two people are available to lift the printer when 
moving it. 

When moving the printer, keep the printer level to avoid toner spillage.

„

If you get toner on your skin, wash it off with cool water and neutral 
detergent. 

WARNING!

If you get toner in your eyes, wash it out immediately with cool water 
and consult a doctor. Material Safety Data Sheets (MSDS) information 
can be found at www.minolta-qms.com (click on the Answer Base).

ACHTUNG! Sollte Toner in Ihre Augen gelangen, die Augen unbedingt 
sofort mit kaltem Wasser ausspülen und einen Artzt aufsuchen. 
MSDS-Informationen (Material Safety Data Sheets; Datenblätter zur 
Materialsicherheit) finden Sie im Internet unter www.minolta-qms.com 
(klicken Sie auf “Answer Base”). Read all caution and warning labels 
carefully, making sure to follow any instructions contained in them. 
These labels are located on the inside of the printer’s covers and the 
interior of the printer body.

„

Make sure any parts removed during cleaning are replaced before you 
plug in the printer.

See “Repacking the Printer” on page 143 for printer storing and shipping 
instructions.

Summary of Contents for MAGICOLOR 2210

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands