MINOLTA-QMS MAGICOLOR 2210 User Manual Download Page 19

Page: 19 / 176

Replacing the OPC Drum Kit

Place the front end of the
laser lens cover into its instal-
lation rail.

Carefully insert the laser lens
cover and check to make sure
it is fully inserted.

Attention

If the laser lens cover is not properly installed, serious damage to
the printer could result.

Continue with replacing the OPC drum cartridge.

Installing the New OPC Drum Cartridge

Remove the new OPC drum
cartridge from its shipping box.

Attention

Keep the protective sheet on the cartridge. Do not touch the
protective sheet on the photosensitive (green) surface or scratch the
surface. This could lower image quality.

Make sure the transfer belt left release lever is still set to its top position
(12 o’clock).

Summary of Contents for MAGICOLOR 2210

















































































































































































Search results

Summary of Contents for MAGICOLOR 2210

Reviews:

Brands by name

Popular brands

MINOLTA-QMS MAGICOLOR 2210, User Manual

Search results

Summary of Contents for MAGICOLOR 2210

Reviews:

Brands by name

Popular brands