REPLACING THE BATTERY
1.
Remove the four screws from battery cover on the bottom of the foot pedal.
2.
Remove battery cover and gasket.
3.
Install the 2 new batteries with the positive (+) side of the battery orientated as shown on pedal.
4.
Reassemble by replacing the gasket and cover.
NOTE:
The batteries must be size AA (not included). It is strongly recommended that a name brand alkaline
battery is used.
COPILOT WIRELESS FOOT PEDAL ACCESSORY
FOR USE IN CONJUNCTION WITH COPILOT SYSTEMS FOR POWERDRIVE V2, POWERDRIVE, AND RIPTIDE SP MOTORS.
FEATURES
Increase Speed
Decrease Speed
Prop ON/OFF
Steer Right
Steer Left
AUDIO MODES
There are three receiver audio modes available. The unit is factory set to Audio Mode 2. To switch between audio modes, insert the audio mode adjustment stick from
the back of the pedal into the slot next to the speed marked “+”. Pushing the stick and the “-” down
simultaneously for two seconds will toggle through the 3 audio modes. The receiver will respond with
1, 2 or 3 audible beeps indicating the corresponding receiver audio mode change.
• Audio Mode 1: All of the normal CoPilot audio patterns (refer to CoPilot
owner’s manual for a complete listing of audio patterns and their meanings).
• Audio Mode 2: Same as audio mode 1 plus an audible beep for speed increase/
decrease and prop on/off.
• Audio Mode 3: Same as audio mode 2 plus the prop on audible click every few seconds.
LEARNING THE FOOT PEDAL
To “learn” the ID number of your foot pedal, follow these steps:
1.
Press and hold the LEARN button located on the side of the receiver (receiver
will emit a continuous tone). A small blunt object must be used to depress the
LEARN button (pen or screwdriver).
2.
Press any button on the foot pedal (receiver will beep 4 times confirming that it
has “learned” the ID number of the foot pedal and that the programming is valid
and complete.
NOTE:
Receiver will store the IDs of up to 10 foot pedals and/or
CoPilot remotes.
ENVIRONMENTAL COMPLIANCE STATEMENT
It is the intention of JOME to be a responsible corporate citizen, operating in compliance with known and applicable envi-
ronmental regulations, and a good neighbor in the communities where we make or sell our products.
WEEE DIRECTIVE:
EU Directive 2002/96/EC “Waste of Electrical and Electronic Equipment Directive (WEEE)” impacts most distributors,
sellers, and manufacturers of consumer electronics in the European Union. The WEEE Directive requires the producer of
consumer electronics to take responsibility for the management of waste from their products to achieve environmentally
responsible disposal during the product life cycle. WEEE compliance may not be required in your location for electrical &
electronic equipment (EEE), nor may it be required for EEE designed and intended as fixed or temporary installation in
transportation vehicles such as automobiles, aircraft, and boats. In some European Union member states, these vehicles
are considered outside of the scope of the Directive, and EEE for those applications can be considered excluded from the
WEEE Directive requirement. This symbol (WEEE wheelie bin) on product indicates the product must not
be disposed of with other household refuse. It must be disposed of and collected for recycling and recovery
of waste EEE. Johnson Outdoors Inc. will mark all EEE products in accordance with the WEEE Directive.
It is our goal to comply in the collection, treatment, recovery, and environmentally sound disposal of those
products; however, these requirement do vary within European Union member states. For more information
about where you should dispose of your waste equipment for recycling and recovery and/or your European
Union member state requirements, please contact your dealer or distributor from which your product was purchased.
DISPOSAL:
Minn Kota motors are not subject to the disposal regulations EAG-VO (electric devices directive) that implements
the WEEE directive. Nevertheless never dispose of your Minn Kota motor in a garbage bin but at the proper place of
collection of your local town council. Never dispose of battery in a garbage bin. Comply with the disposal directions ofthe
manufacturer or his representative and dispose of them at the proper place of collection of your local town council.
FCC ID: T62-WFTA
IC: 4397A-T62WFTA
MODEL: FOOT PEDAL
The FCC and IC label can be found
on the back side of the remote.
FCC AND INDUSTRY CANADA
COMPLIANCE STATEMENT:
This device complies with FCC
Rules Part 15 and Industry Canada
RSS-210. Operation is subject to
the following two conditions:
(1) This device may not cause harm-
ful interference
(2) This device must accept any
interference, including interference
that may cause undesired operation
of the device
Changes or modifications not
expressly approved by the party re-
sponsible for compliance could void
the user’s authority to operate the
equipment. Per FCC Part 15.21.
RADIO OPERATION:
• Frequency band: 433.92 MHz
• Maximum RF power transmitted:
+7 dBm
