MINN KOTA 1854053 Manual Download Page 1

MKA-53/RTA-54 ELECTRIC STEER  

COMPOSITE RELEASE BRACKET 

1854053 & 1854054

TOOLS AND RESOURCES REQUIRED

Item /  

Assembly

Part #

Description

Qty. 

Items 2-16

2994935

BAG ASM, HT COMP QRB

1

2

2372633

PIN-PADLOCK MAX/AT QCK REL.

1

4

2373484

SCREW-1/4-20 X 7/8 PFH SS

1

6

2260800

CLIP-HAIR SPRING,SS,MAX BG

1

8

2223446

SCREW-1/4-20 X 2" PFH SS

6

10

2371712

WASHER-FLAT 9/32 X 5/8 X 1/16

6

12

2373482

SCREW-1/4-20 X 3" PFH SS

4

14

2261713

WASHER-1/4 FLAT 18-8 SS

4

16

2073100

NUT-HEX 1/4-20 NYLOC-JAM SS

10

Items 18-22

2990955

HANDLE ASM, HT COMP QRB

1

18

HANDLE, SS, HT COMP QRB

1

20

PIN-LOCKING, SS,  HTC QRB

2

22

SCREW-5/16-18 X 3/4 BHCS SS

2

Items 24-26

2991690

PLATE ASM,  BLACK, HTC QRB

1

2991691

PLATE ASM,  WHITE, HTC QRB

1

24

2371690

PLATE-INNER, BLACK, HTC QRB

1

2371691

PLATE-INNER, WHITE, HTC QRB

1

26

2371692

PLATE-OUTER, BLACK, HTC QRB

1

2371693

PLATE-OUTER, WHITE, HTC QRB

1

28

2378848

STIFFENER-PLATE/PUCK,BLK

1

2378849

STIFFENER-PLATE/PUCK,WHT

1

p

2374951

INSTRC. HT COMPOSITE QRB

1

22

24

26

B

12

14

10

16

8

A

•  #3 Phillips Screw Driver
•  Drill 

•  Scissors
•  17/64” Drill Bit

•  7/16” Box End Wrench
•  33/64 (.516”) Drill Bit

•  A second person to help with 

the installation

p

 

Not shown on Parts Diagram.

 

 This part is included in an assembly and cannot be ordered individually. 

The MKA-53 is recommended with the Ulterra™, Terrova®, PowerDrive™, PowerDrive V2 and the Pontoon PowerDrive™ Minn Kota® Motors and 
the Deckhand 40. The RTA-54 is recommended with the RT Ulterra™, RT Terrova®, RT PowerDrive™ and RT PowerDrive V2 Minn Kota® Motors.

20

18

28

4

2

6

C

MOUNTING CONSIDERATIONS

Complete Typical Installation

It is recommended that the motor be mounted as close to the 
centerline of the boat as possible. The motor must not encounter 
any obstructions as it is lowered into the water or raised into the 
boat when stowed and deployed. Make sure the motor rest is 
positioned far enough beyond the edge of the boat. Make sure the 
area under the mounting location is flat, clear to drill holes and 
install nuts and washers.

NOTICE:

 Images are a graphical representation and  

may vary from your motor. 

Save the box! A template for 

installation is printed on the inside of the box.

 minnkotamotors.com  |  1  

©2019 Johnson Outdoors Marine Electronics, Inc.

Summary of Contents for 1854053















Reviews: