Minebea CC-Link CSD-892-73 Instruction Manual Download Page 21

Page: 21 / 159

tio

n &

irin

2-4. Connecting of power supply and ground

Please connect the power supply and ground to the lower terminal block as shown in the

following

ﬁ

gure.

F.G.
+24 V

Frame ground
Power supply DC24V

0 V

Power supply DC

㸮

DC24V

(Permissible variable range : DC20.4 V ~ DC27.6 V)

D-class with

single earth

•

Please ground the protective ground terminal by D-class with single earth.

Otherwise, it may cause an unexpected malfunction because of the in

ﬂ

uence of

noise from the other equipment.

•

Please refer to [5. Applied standard] in [Safety Precaution] about the grounding to

comply with CE Standard.

•

Please connect the power supply and the ground surely as shown in the

ﬁ

gures and also use

within the regulated power supply condition.

CAUTION

Summary of Contents for CC-Link CSD-892-73
































































































































































Search results

Summary of Contents for CC-Link CSD-892-73

Reviews:

Minebea CC-Link CSD-892-73, Instruction Manual, Page: 21 / 159

Search results

Summary of Contents for CC-Link CSD-892-73

Reviews: