Minebea Intec Puro Operating Instructions Manual Download

Page: 13 / 61

Item

Description

Item

Description

Auto Taring Symbol

Pieces

LED indicators

When the device is switched on, the battery status LED (1) lights red while the battery is
charging and green when the battery is fully charged.

The colored LED indicators (2) on the right side of the control panel are used in Check
mode (see Chapter

5.2.3

) and will light up according to the following rules:

(Red) Weight value > upper tolerance limit
(Green) Weight value ≤ ≥ is within OK range
(Yellow) Weight value < lower tolerance limit

4.1.1.3

Operating elements

Button

Off

Mode

Unit

Primary Function

On / Zero

Tare

M+

Function

Print

(short press) < 1
second

Power on the
scale (when
scale is off).
Set zero (when
scale is on).

Set a tare value. Accumulates

the weight or
display the
accumulated
information.

Triggers a func-
tion.

Sends the current
value to the selected
COM ports if AUTO-
PRINT is set to off.

Secondary
Function

Off

Menu

Mode

Unit

4 Device description

Weight indicator Puro®

Minebea Intec

EN-11

Summary of Contents for Puro






























































Search results

Summary of Contents for Puro

Reviews:

Related manuals for Puro

Brands by name

Popular brands

Minebea Intec Puro, Operating Instructions Manual

Search results

Summary of Contents for Puro

Reviews:

Related manuals for Puro

Brands by name

Popular brands