Minebea Intec Contego Installation Manual Download Page 37

Page: 37 / 44

If shaft (8) or/and roller (7) cannot be moved, the weighing module is distorted and

must be adjusted:

9.1.3

Replacing the load cell

WARNING

The vessel may turn over during de-/mounting.

Securing the vessel against tipping is imperative.

Use an appropriate lifting jack.

NOTICE

Defects in the load cell may occur.

Do not lift or transport load cells by pulling the cable.

Note:
Load cell cable gland

When turning, the position of the gland remains unchanged. Only the inner clamping is

released.

14. Re-screw the stopper (5) together with the ilm on the lower plate (9). Make sure to

use the correct tightening torque, see Chapter

5.2

15. Release the screws (6).
16. Shift the stopper (5), until shaft (8) or/and roller (7) can move freely again.
17. Re-tighten the screws (6). Make sure to use the correct tightening torque, see

Chapter

5.2

18. Fit the bellow, press it irmly into the groove of the upper and lower plate

circumferentially, and make sure that the transitions are lush.

1. Release the load cell cable in the junction box, pull it out carefully and roll it up.

9 Servicing/repairs/cleaning

Hygienic Weighing Module Contego®

Minebea Intec

EN-35

Summary of Contents for Contego













































Search results

Summary of Contents for Contego

Reviews:

Related manuals for Contego

Brands by name

Popular brands

Minebea Intec Contego, Installation Manual

Search results

Summary of Contents for Contego

Reviews:

Related manuals for Contego

Brands by name

Popular brands