manualshive.com logo in svg

Minebea Intec CAS1, Operating Instructions Manual, Page: 54 / 160

Share
Download
Minebea Intec CAS1 Operating Instructions Manual Download Page 54

SM)

only visible in service mode

Procedure

If the device is part of a veriied weighing system, this can only be done by breaking

the seal. The scale must then be re-calibrated.

The data can be obtained from the land registry or the land surveying authority.

5.6.3.1

Displaying the geographical values during the calibration procedure

Note:

The set geographic values are displayed during the calibration procedure if the display

of this data is activated in the setup menu at [BETRIEB].
Menu: [SETUP]- [BETRIEB]- [PARAMET]- [ANZ.GEOG]- [EIN] (8.12.1) (factory setting:

[AUS] 8.12.2, display deactivated) (see also Chapter

6.3.6.1

).

When the display is activated, the calibration procedure is as follows:

After starting the calibration procedure, when using local altitude and latitude, [CAL] ,

the word [ALTITUD] followed by the set altitude (in meters above sea level) appears

briely on the display.

5.6.4

Entering calibration and linearization weights

Enter the calibration and linearization weights.

1. Open the locking switch (see Chapter

7.2.1

).

2. Activate service mode (see Chapter

5.6.2

).

3. Select the weighing platform.
4. Enter the geographical data for the calibration site under menu item [GEOG.DAT]

1.20.1 … 1.20.3 and save it under menu item [SPEICH.] 1.20.4(see also

Chapter

6.3.1.1.1

).

5. Perform external calibration (see Chapter

7.2

).

6. After calibration, enter the geographical data for the installation site under menu

item [GEOG.DAT] 1.20.1 … 1.20.3 and save it under menu item [SPEICH.] 1.20.4(see

also Chapter

6.3.1.1.1

).

7. Close the locking switch.

The scale can now be operated at the installation site, including the tolerance

zone speciied above.

1. Conirm the value displayed with the

key (cancel with the

key).

The word [LATITUD] is then briely displayed followed by the set latitude in

degrees.

2. Conirm the value displayed with the

key (cancel with the

key).

Then the prompt to place the calibration weight onto the scale is displayed. If the

gravitational acceleration has been entered instead of the local altitude and

latitude, the word [GRAVITY] appears briely followed by the set value for the

gravitational acceleration.

3. Conirm the value displayed with the

key (cancel with the

key).

Combics 1 Series Complete Scales Models CAW1P, CAW1S, CAS1

5 Getting started

EN-52

Minebea Intec

Summary of Contents for CAS1

































































































































































Reviews:

No comments