manualshive.com logo in svg

Minebea Intec CAS1, Operating Instructions Manual, Page: 43 / 160

Share
Download
Minebea Intec CAS1 Operating Instructions Manual Download Page 43

4.3 Accessories

4.3.1

Printer

Product

Order No.

Veriiable data printer with date/time and statistics functions with LCD

display.

YDP21

5 x 40 m paper rolls for data printer

6903952

Replacement ink ribbon cartridge for printer

6906918

Veriiable strip and label printer with barcode printout, paper width

108 mm, with adapter cable (12-pin round male connector) and external

power supply.

ZD420d

Veriiable strip and label printer with barcode printout, paper width

108 mm and external power supply.

ZD420t

Ink ribbon for ZD420t

69Y03234

Labels for ZD420d:

101 x 127 mm (305 labels)

69Y03195

Printing paper for ZD420d

1 paper roll 101 mm x 75 m, thermal paper

69Y03196

Veriiable strip and label printer with thermal print head, paper width

60 mm, with adapter cable and external power supply.

YDP05

Adapter cable for CAW*P

YCC01-

01CISLM3

Adapter cable for CAW*S, CAS

YCC02-D09M6

Ink ribbon for ZD420t

3 paper rolls YDP05

60 mm x 75 m, thermal paper

69Y03090

Labels, small, 58 mm x 30 mm, 1000 labels

69Y03092

Labels, medium, 58 mm x 76 mm, 500 labels

69Y03093

Labels, large, 58 mm x 100 mm, 350 labels

69Y03094

4.3.2

Optional interface (UniCOM)

Product

Order No.

For optional interface (UniCOM)

CAW1P

CAW1S, CAS1

For installation in: IP44

IP69K

version

Interface module (RS

‑

232)

–

●

YDO02C-232

Interface module (RS

‑

422 and RS

‑

485) galvanically isolated

–

●

YDO02C-485

Galvanically isolated digital I/Os, 5 outputs and 5 inputs user-

deinable

–

●

YDO02C-DIO

4 Device installation

Combics 1 Series Complete Scales Models CAW1P, CAW1S, CAS1

Minebea Intec

EN-41

Summary of Contents for CAS1

































































































































































Reviews:

No comments