manualshive.com logo in svg

Mindray Passport V, Operating Instructions Manual

The Mindray Passport V is an advanced medical device offering cutting-edge features and technology. Gain comprehensive knowledge about its functionalities and maintenance by accessing the Service Manual, available for free download from our website. Enhance your product understanding and ensure efficient usage of this remarkable equipment.

Share
Download
background image

Monitor Setup Menu

System Configuration

2 - 6

0070- 0-0704-02

Passport V Operating Instructions

2.3

Monitor Setup Menu

Select the Monitor Setup Menu to configure audio and display settings.

FIGURE 2-3

Monitor Setup Menu

To access the Monitor Setup Menu:

1.

Power up the 

Passport V

. The normal screen is displayed.

2.

Rotate the Navigator Knob to 

Monitor Setup

. Press the knob to select it.

3.

Configure the settings as desired.

4.

To exit, press the 

Normal Screen 

key on the front panel.

The following table describes the 

Monitor Setup Menu

 selections:

MENU TITLE

ON SCREEN

MENU CHOICES

DEFAULT

COMMENTS

Normal Screen

Select to return to Normal Screen (or 
press the 

Normal Screen 

key on the 

front panel).

Display Setup

Select to make changes to the display 
format. Save as defaults if desired.

Alarm Volume 

low to high volume

Mid-level

Select to change alarm volume.

Beep Volume

silence to high volume

Mid-level

Select to change systole beep volume.

Color

Select to access Color Setup Menu.

Advanced Setup

Select to access Advanced Setup 
Menu.

0

Summary of Contents for Passport V

































































































































































































































































































Reviews:

No comments

Related manuals for Passport V

Geberit 501074001 Quick Manual preview
501074001
Brand: Geberit Pages: 64
Prevue Hendryx Charming Aviary F035 Instructions Manual preview
Charming Aviary F035
Brand: Prevue Hendryx Pages: 9
Caretrak Mobile Defender User Manual preview
Mobile Defender
Brand: Caretrak Pages: 16
T3 CONVERTIBLE Series User Manual preview
CONVERTIBLE Series
Brand: T3 Pages: 44
mind alive DAVID ALERT Operator'S Manual preview
DAVID ALERT
Brand: mind alive Pages: 15
Orliman Lumbitron LT-310 Use And Maintenance Instructions preview
Lumbitron LT-310
Brand: Orliman Pages: 12
mychway SR-MJ1804 User Manual preview
SR-MJ1804
Brand: mychway Pages: 28
SpotOn Virtual Fence User Manual preview
Virtual Fence
Brand: SpotOn Pages: 15
nedis 5412810331017 Quick Start Manual preview
5412810331017
Brand: nedis Pages: 34
4pets ECO Instructions For Assembly preview
ECO
Brand: 4pets Pages: 2
Perfect Fit 250196 Manual preview
250196
Brand: Perfect Fit Pages: 10
ProMed 204006 Instruction Leaflet preview
204006
Brand: ProMed Pages: 164
Tri-Tronics SPORT JUNIOR Manual preview
SPORT JUNIOR
Brand: Tri-Tronics Pages: 26
Lanaform LA131312 Manual preview
LA131312
Brand: Lanaform Pages: 28
Zolia STOOLY Assembly Instructions Manual preview
STOOLY
Brand: Zolia Pages: 8
Patpet P-COLLAR 920 User Manual preview
P-COLLAR 920
Brand: Patpet Pages: 11
Tractive TRATR2 User Manual preview
TRATR2
Brand: Tractive Pages: 44
VERSHOLD IB-8553 Quick Start Manual preview
IB-8553
Brand: VERSHOLD Pages: 4

Brands by name

Popular brands

Load more brands