background image

, inc.

Mincey Marble Mfg., Inc.

4321 Browns Bridge Road

Gainesville, GA 30504

Ph: 800.533.1806

Fx: 770.531.0935

www.minceymarble.com 

 

MATERIALS / TOOLS NEEDED CHECKLIST

 

PRE-INSTALLATION PIECES / PARTS LIST

 

ENCLOSURE SYSTEM INSTALLATION

Installation Instructions for Mincey Marble  

Manufacturing’s Arezzo Bypass Barn Door Shower Enclosures

ATTENTION:  Prior to starting the installation, please read through these instructions.  This 

will help avoid any unneccesary breakage.  Any breakage due to handling or installing this 

enclosure system is the responsibility of the installer and is not covered under the Mincey 

Warranty.  Mincey recommends that two people are used to install this shower enclosure 

system due to the weight and fragility of the glass panels.  Mincey also recommends that  

you protect the glass, especially the bottoms, and the shower pan during installation.

These installation instructions apply to the Mincey Arezzo Bypass Barn Door Shower Enclosure System.  In these  

instructions we are going to use an example with a 60” wide shower.  

All Drawings Are Not To Scale.

8QFUDWHDOORIWKHPDWHULDOVDQGFRQ¿UPWKDWDOORIWKHSDUWVDQGSLHFHVDUHSUHVHQW

  The Required 

Tools are listed below.  The contents of the Hardware Kit are listed below.  The Parts Diagram is on the following 

page.  Before you begin the installation, make sure that all of the pertinent surfaces are clean and free of dust, 

debris and any shavings.  After you perform any drilling, you will want to make sure the surfaces are clean again 

- this includes the Shower Pan and the Shower Panel Walls.

 

MATERIALS / TOOLS NEEDED

 

INCLUDED IN THE HARDWARE KIT

ROLLERS QTY: 4

GLASS DOOR

RETENTION

PIECES

QTY: 4

BUMPERS

QTY: 8

CENTER DOOR 

GUIDE QTY: 1

END DOOR 

GUIDES QTY: 2

1/8”

QTY: 2

3/16”

ALLEN 

WRENCHES

WALL 

ANCHORS

QTY: 8

1 1/4” 

SCREWS

QTY: 8

7/16” 

SCREWS

QTY: 8

BUMPER

SCREW

COVERS

QTY: 8

DRILL (CORDED OR CORDLESS),

5/16” MASONRY DRILL BIT,

1/8” METAL DRILL BIT

TAPE MEASURE

PENCIL

LEVEL

CAULK GUN,

100% SILICONE

RUBBER MALLET

PORTABLE BAND SAW

(PREFERRED METHOD)

HACK SAW

- OR -

PHILLIPS HEAD SCREWDRIVER

LOCTITE

BLUE 243

THREADLOCKER

Summary of Contents for Arezzo Bypass Barn Door








Reviews: