background image

2

Foreword

Thank you very much for your purchase of the Mimaki Bulk Ink System "MBIS3".

About This Operation manual

• This Operation manual describes the operation and maintenance of "TPC-1000" (hereafter referred to as "this

machine").

• Please read and fully understand this Operation manual before putting the machine into service. It is also

necessary to keep this Operation manual on hand.

• Make arrangements so that this manual is certainly delivered to the person in charge of the operation of this

machine.

• This Operation manual has been carefully prepared for your easy understanding. However, please do not

hesitate to contact a distributor in your district or our office if you have any inquiry.

• Description contained in this Operation manual are subject to change without notice for improvement.
• In the case where this Operation manual should be illegible due to destruction or lost by fire or breakage,

purchase another copy of the Operation manual from our office.

Caution

DISCLAIMER OF WARRANTY: THIS LIMITED WARRANTY OF MIMAKI SHALL BE THE SOLE AND EXCLUSIVE
WARRANTY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO, ANY IMPLIED WARRANTY OF

 

MERCHANTABILITY OR FITNESS, AND MIMAKI NEITHER ASSUMES

NOR AUTHORIZES DEALER TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABILITY OR MAKE ANY OTHER
WARRANTY OR MAKE ANY OTHER WARRANTY IN CONNECTION WITH ANY PRODUCT WITHOUT MIMAKI'S
PRIOR WRITTEN CONSENT.

IN NO EVENT SHALL MIMAKI BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR FOR
LOSS OF PROFITS OF DEALER OR CUSTOMERS OF ANY PRODUCT.

Requests

• This Operation manual has been carefully prepared for your easy understanding. However, please do not

hesitate to contact a distributor in your district or our office if you have any inquiry.

• Description contained in this Operation manual are subject to change without notice for improvement.

Unauthorized reproduction of this manual is strictly prohibited.

MIMAKI ENGINEERING Co., Ltd.

All Rights Reserved.Copyright

 

Summary of Contents for MBIS3

















Reviews: