MIMAKI CG-FX SERIES Operation Manual Download Page 29

Page: 29 / 142

– 1.13 –

Connecting the cables

* When connecting the cables, turn off first the power to the device and that to

the host computer which the power cable is to be connected.

* Do not insert/remove the cable during data transferring.

* For details on USB connection, refer to attached USB install guide.

* Follow the instructions in case the wizard displayed when connected a USB

cable.

Connecting the interface cables

The device comes with two different kinds of interfaces.

Select either one that matches the host computer.

•

RS-232C compatible interface

•

USB interface

* It is necessary the settings of interface which to use.

* Plug in/out the connecter carefully. Too much pressure may damage the

connecter.

Connecting the power cables

After the completion of interface cable connection, connect the power cable.

Connect the power cable to the receptacle of the following power specification.

•

Voltage

AC100V to 240V

10%

•

Frequency

50/60Hz

•

Capacity

100W or more (equivalent to 2 A)

USB interface

RS-232C
compatible interface

Summary of Contents for CG-FX SERIES















































































































































Search results

Summary of Contents for CG-FX SERIES

Reviews:

Related manuals for CG-FX SERIES

Brands by name

Popular brands

MIMAKI CG-FX SERIES, Operation Manual

Search results

Summary of Contents for CG-FX SERIES

Reviews:

Related manuals for CG-FX SERIES

Brands by name

Popular brands