background image

RouterBOARD 493/AH/G

User's Manual

(1-Sep-2011)

Copyright and Warranty Information

Copyright   and   Trademarks.   Copyright   MikroTikls   SIA.   This   manual   contains   information   protected   by 

copyright law. No part of it may be reproduced or transmitted in any form without prior written permission  

from the copyright holder. RouterBOARD, RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls 

SIA. All trademarks and registered trademarks appearing in this manual are the property of their respective 

holders.

Hardware

. MikroTik warrants all RouterBOARD series equipment for the term of fifteen (15) months from 

the shipping date to be free of defects in materials and workmanship under normal use and service, except 

in case of damage caused by mechanical, electrical or other accidental  or intended damages caused by  

improper use or due to wind, rain, fire or other acts of nature.

To return failed units to MikroTik, you must perform the following RMA (Return Merchandise Authorization)  

procedure. Follow the instructions below to save time, efforts, avoid costs, and improve the speed of the 

RMA process.

1.   If   you   have   purchased   your   product   from   a   MikroTik   Reseller,   please   contact   the   Reseller   company 

regarding   all   warranty   and   repair   issues,   the   following   instructions   apply   ONLY   if   you   purchased   your 

equipment directly from MikroTik in Latvia.

2. MikroTik does not offer repairs for products that are not covered by warranty. Exceptions can be made  

for: RB/1000, RB/1000U, RB/600, RB/600A and RB/800

3. Out-of-warranty devices and devices not covered by warranty sent to Mikrotik will be returned to the 

sender at sender's cost.

RMA Instructions are located on our webpage here: 

http://rma.mikrotik.com

Manual. This manual is provided “as is” without a warranty of any kind, expressed or implied, including, but 

not   limited   to,   the   implied   warranty   of   merchantability   and   fitness   for   a   particular   purpose.   The 

manufacturer has made every effort to ensure the accuracy of the contents of this manual, however, it is 

possible that it may contain technical inaccuracies, typographical or other errors. No liability is assumed for 

any   inaccuracy   found   in   this   publication,   nor   for   direct   or   indirect,   incidental,   consequential   or   other 

damages that may result from such an inaccuracy, including, but not limited to, loss of data or profits. 

Please report any inaccuracies found to [email protected]

Summary of Contents for RouterBOARD 493












Reviews: