background image

RouterBOARD 493/AH/G

User's Manual

(1-Sep-2011)

Copyright and Warranty Information

Copyright   and   Trademarks.   Copyright   MikroTikls   SIA.   This   manual   contains   information   protected   by  
copyright law. No part of it may be reproduced or transmitted in any form without prior written permission  
from the copyright holder. RouterBOARD, RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls 
SIA. All trademarks and registered trademarks appearing in this manual are the property of their respective 
holders.

Hardware

.  MikroTik warrants all RouterBOARD series equipment for the term of fifteen (15) months from 

the shipping date to be free of defects in materials and workmanship under normal use and service, except  
in   case   of   damage   caused   by  mechanical,   electrical  or   other   accidental   or  intended   damages  caused   by 
improper use or due to wind, rain, fire or other acts of nature.

To return failed units to MikroTik, you must perform the following RMA (Return Merchandise Authorization)  
procedure. Follow the instructions below to save time, efforts, avoid costs, and improve the speed of the  
RMA process.

1.   If   you   have   purchased   your   product   from   a   MikroTik   Reseller,   please   contact   the   Reseller   company 
regarding   all   warranty   and   repair   issues,   the   following   instructions   apply   ONLY   if   you   purchased   your  
equipment directly from MikroTik in Latvia.

2. MikroTik does not offer repairs for products that are not covered by warranty. Exceptions can be made 
for: RB/1000, RB/1000U, RB/600, RB/600A and RB/800

3. Out-of-warranty devices and devices not covered by warranty sent to Mikrotik will be  returned  to the  
sender at sender's cost.

RMA Instructions are located on our webpage here: 

http://rma.mikrotik.com

Manual. This manual is provided “as is” without a warranty of any kind, expressed or implied, including, but 
not limited to, the implied warranty of merchantability and fitness for a particular purpose. The manufacturer 
has made every effort to ensure the accuracy of the contents of this manual, however, it is possible that it  
may contain technical inaccuracies, typographical or other errors. No liability is assumed for any inaccuracy 
found  in this  publication,  nor  for  direct  or  indirect,   incidental,   consequential  or  other damages  that  may 
result   from   such   an   inaccuracy,   including,   but   not   limited   to,   loss   of   data   or   profits.   Please   report   any 
inaccuracies found to [email protected]

Summary of Contents for RouterBOARD 493/AH/G












Reviews: