Miele WWR860 Operating Instructions Manual Download Page 51

Page: 51 / 116

Garment care label symbols

Washing

The figure quoted in the bucket is the
maximum temperature at which the
garment can be washed.



Normal agitation



Reduced agitation



Much reduced agitation



Hand wash



Do not wash

Programme selection
examples

Programme

Garment care label

symbols

Cottons




Minimum iron



Delicates



Woollens





Silks





Express 20



Automatic plus



Drying



Normal temperature



Low temperature



Do not tumble dry

Ironing



Approx. 200 °C



Approx. 150 °C



Approx. 110 °C

Ironing with steam can cause
irreversible damage.



Ironing prohibited

Professional cleaning



Dry clean only. The letters
indicate the type of cleaning
agent required.





Wet cleaning



Dry cleaning prohibited

Bleaching



Any oxidation bleach can be
used



Use oxygen bleach only



Do not bleach

Summary of Contents for WWR860





















































































































Search results

Summary of Contents for WWR860

Reviews:

Related manuals for WWR860

Brands by name

Popular brands

Miele WWR860, Operating Instructions Manual

Search results

Summary of Contents for WWR860

Reviews:

Related manuals for WWR860

Brands by name

Popular brands