Miele WWR860 Operating Instructions Manual Download Page 19

Page: 19 / 116

Before using for the first time



Damage resulting from incorrect

installation and connection.
Installing and connecting the
washing machine incorrectly will
cause serious damage to property.
See “Installation”.

This washing machine has undergone
a complete functional test at the
factory and there will be some residual
water in the drum from this process.

Removing the protective foil
and advertising stickers



Remove:

- the protective foil from the door (if

present).

- any advertising stickers from the front

and the lid.

Please do not remove any labels
(e.g. the data plate) which are visible
when you open the door.

Remove the detergent
cartridges and the drain hose
elbow from the drum

Two detergent cartridges for automatic
detergent dispensing and an elbow
piece for the drain hose are stored in
the drum.



Pull open the door.



Take the two cartridges and the
elbow piece out of the drum.



Shut the door with a gentle swing.

Summary of Contents for WWR860





















































































































Search results

Summary of Contents for WWR860

Reviews:

Related manuals for WWR860

Brands by name

Popular brands

Miele WWR860, Operating Instructions Manual

Search results

Summary of Contents for WWR860

Reviews:

Related manuals for WWR860

Brands by name

Popular brands