Miele WTD 160 Operating Instructions Manual Download Page 30

Page: 30 / 100

WASHING

Tip:

Leave the door slightly open to al-

low the drum to dry.



If applicable, remove the used cap-
sule from the detergent drawer.

Tip:

Leave the detergent drawer slightly

open to allow it to dry.

Spin speeds

Final spin speed in wash programme

When a programme is selected, the
sensor control for the optimum spin
speed for that wash programme will be
brightly lit up in the control field.

A faster spin speed can be selected for
certain wash programmes.

The highest selectable spin speed is in-
dicated in the table.

Programme

rpm

ECO 40-60

1500

Cottons

1500

Minimum iron

1200

Delicates

900

Woollens

1200

Rinse/Spin

1500

Express

1200

Dark garments/Denim

900

Shirts

900

Rinse-spin

There is a spin cycle after the main
wash and between the rinse cycles. A
reduction in the final spin speed will
also reduce the rinse-spin speed as ap-
propriate.

Summary of Contents for WTD 160





































































































Search results

Summary of Contents for WTD 160

Reviews:

Related manuals for WTD 160

Brands by name

Popular brands

Miele WTD 160, Operating Instructions Manual

Search results

Summary of Contents for WTD 160

Reviews:

Related manuals for WTD 160

Brands by name

Popular brands