Miele WTD 160 Operating Instructions Manual Download Page 23

Page: 23 / 100

WASHING

3. Selecting a programme

Switching the washer-dryer on



Turn the programme selector to a
programme.

The control field lights up.

Selecting a programme



Turn the programme selector to the
required programme.

The estimated wash time is shown on
the time display and the pre-set tem-
perature and spin speed light up in the
control field.

Using the

MobileStart

programme

selector position



Turn the programme selector to the

MobileStart



position.

Tip:

In order to use

MobileStart



, the

washer-dryer must be logged on to the
WiFi network and

Remote control

must

be switched on.

Once the programme has started, the
washer-dryer can be operated with the
Miele@mobile app.

Selecting washing



Touch the

Washing

Drying

sensor

control until just the

Washing

sensor

control is brightly lit up.

The

Drying

sensor control must only

light up dimly as otherwise the wash
programme would be followed im-
mediately by the relevant drying pro-
gramme.

Summary of Contents for WTD 160





































































































Search results

Summary of Contents for WTD 160

Reviews:

Related manuals for WTD 160

Brands by name

Popular brands

Miele WTD 160, Operating Instructions Manual

Search results

Summary of Contents for WTD 160

Reviews:

Related manuals for WTD 160

Brands by name

Popular brands