manualshive.com logo in svg

Miele WCI 320, Operating Instructions Manual

Share
Download
Miele WCI 320 Operating Instructions Manual Download Page 64

Problem solving guide

64

The door will not open

Problem

Cause and remedy

The door cannot be
pulled open during a
programme.

The door is locked during a programme.

Touch the 

Start/Stop

 sensor to cancel the

programme.

The programme is cancelled, the door will unlock and
you will be able to pull it open.

There is still water in the drum and the machine is
unable to drain.

Clean the drain filters and the drain pump as
described in “Opening the door in the event of a
blocked drain outlet and/or power failure”.

Comfort cooling

appears in the display
after a programme has
been cancelled.

To protect the user against scalding, the door cannot
be opened if the suds temperature is higher than
55 °C.

Wait until the temperature in the drum has
decreased and the message has gone out in the
display.

The following appears
in the display:

 

 Service Door release

fault F35

The door lock has jammed.

Call Miele.

Summary of Contents for WCI 320





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands