Miele W 1514 Operating Instructions Manual Download | Manualshive

Page: 46 / 60

background image

Levelling the machine

The machine must stand perfectly level
on all four feet to ensure safe and
proper operation.

Incorrect installation may increase
electricity and water consumption and
may cause the machine to move about.

Screwing out and adjusting the feet

The four adjustable screw feet are used
to level the machine. All four feet are
screwed in when the machine is
delivered.

^

Using the spanner supplied turn
counter nut

2

in a clockwise

direction. Then turn counter nut

2

together with foot

1

to unscrew.

^

Use a spirit level to check the
machine is standing level.

^

Hold foot

1

securely with a pipe

wrench. Turn counter nut

2

again

using the spanner supplied until it
sits firmly up against the housing.

,

All four counternuts must be

firmly up against the housing. Please
also check this for the feet which did
not need adjustment. Otherwise
there is the danger of the machine
moving about.

Installation and connection

46

«
...
44
45
46
47
48
...
»

Summary of Contents for W 1514





























































Reviews:

No comments

Related manuals for W 1514

Brand: Fasa Pages: 17

Brand: VOX electronics Pages: 154

Brand: Metos Pages: 52

Brand: Saba Pages: 39

Brand: F.F. Group Pages: 68

Brand: Hanseatic Pages: 72

Brand: Black Max Pages: 56

Brand: grandimpianti Pages: 85

Brand: Scandomestic Pages: 151

HDS 3.5/23-4M Eg

Brand: Kärcher Pages: 48

Brand: AEG Electrolux Pages: 108

Brand: GE Pages: 48

Brand: Gaggenau Pages: 72

Brand: Kärcher Pages: 19

K4 Premium Power Control

Brand: Kärcher Pages: 11

K7 Premium Smart Control

Brand: Kärcher Pages: 13

Brand: Kärcher Pages: 26

Brand: Kärcher Pages: 144

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands