Miele TXR 860 WP Operating Instructions Manual Download Page 22

Page: 22 / 100

Initial commissioning

Switching on the tumble dryer



Press the



button.

The welcome screen will light up.

The display will guide you step by step
through the initial commissioning
process.

Setting the display language

You will be asked to select the display
language. It is possible to change the
language at any time via the Settings
menu.

english (AU)

english (CA)

english (GB)

english (US)

Language

deutsch

dansk



Scroll to the left or the right until the
language you want appears.



Touch the sensor button for the
language you want.

The selected language will be
highlighted in orange and the display
will change to the next setting.

Setting up Miele@home

Skip

Continue

Set up “Miele@home”?





To set up Miele@home now: touch
the

Continue

sensor button.

Summary of Contents for TXR 860 WP





































































































Search results

Summary of Contents for TXR 860 WP

Reviews:

Related manuals for TXR 860 WP

Brands by name

Popular brands

Miele TXR 860 WP, Operating Instructions Manual

Search results

Summary of Contents for TXR 860 WP

Reviews:

Related manuals for TXR 860 WP

Brands by name

Popular brands