Miele TEL 785 WP Operating Instructions Manual Download Page 57

Page: 57 / 100

Cleaning and care

Fluff filters

This tumble dryer has 2 fluff filters in the
loading area of the door. Both fluff fil-
ters trap fluff produced during the dry-
ing process.

Clean the fluff filters after each drying
programme. This prevents an exten-
sion of the programme running time.

Also clean the fluff filters when the fol-
lowing message lights up in the dis-
play:

Clean the plinth filter. See 



To clear the message, confirm with

Removing the fragrance flacon

The intensity of the fragrance will be di-
minished if the fluff filters and the plinth
filter are not cleaned.



Remove the fragrance flacon. See
“Fragrance flacon”, “Removing/repla-
cing the fragrance flacon”.

Removing visible fluff

Tip:

You can also use a vacuum cleaner

so that you can remove the fluff without
touching it.



Open the door.



Pull the upper fluff filter forwards to
remove it.



Remove the fluff (see arrows).

Summary of Contents for TEL 785 WP





































































































Search results

Summary of Contents for TEL 785 WP

Reviews:

Related manuals for TEL 785 WP

Brands by name

Popular brands

Miele TEL 785 WP, Operating Instructions Manual

Search results

Summary of Contents for TEL 785 WP

Reviews:

Related manuals for TEL 785 WP

Brands by name

Popular brands