Miele TDA 140 C Operating Instructions Manual Download Page 48

Page: 48 / 60

Programmable functions

Altering the residual moisture

level in the Cottons

programme

The tumble dryer is designed to dry

effectively using as little energy as

possible. However, if you require the

laundry to be drier or damper, you can

reduce or increase the default residual

moisture in this programme.

Exception: The

Normal

drying level

remains unchanged.

Follow steps (







...) to

programme and store in memory.
Before you begin, ensure that:

– The tumble dryer is switched off.
– The door is closed.
– The programme selector is pointing

Finish



Press

Start

and keep it pressed in

whilst carrying out steps







Switch the dryer on.



Wait until the indicator light for the

Start

button lights up constantly . . .



. . . and then release the

Start

button.

The

Empty container

indicator light will

flash once.

The option selected will be displayed

by a

number

which will alternate with





Laundry will be damper



Factory default setting

(The

Clean out airways

indicator light

will also flash once)



Laundry will be drier

(The

Clean out airways

indicator light

will also flash twice)



Pressing the

Start

button switches

between the options.



Switch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:



Carry out steps







Switch the dryer off after checking.

Summary of Contents for TDA 140 C





























































Search results

Summary of Contents for TDA 140 C

Reviews:

Related manuals for TDA 140 C

Brands by name

Popular brands

Miele TDA 140 C, Operating Instructions Manual

Search results

Summary of Contents for TDA 140 C

Reviews:

Related manuals for TDA 140 C

Brands by name

Popular brands