Miele TCE 620 WP Operating Instructions Manual Download Page 67

Page: 67 / 76

Programmable functions



Cotton drying levels

You can adjust the drying levels for the

Cottons

programme to one of 7

different levels.

Options



= even damper



= damper



= a little damper



Factory default setting



= a little drier



= drier



= even drier

Exception:
The

Cottons



programme will

remain unchanged.



Minimum iron drying levels

You can adjust the drying levels for the

Minimum iron

programme to one of 7

different levels.

Options



= even damper



= damper



= a little damper



Factory default setting



= a little drier



= drier



= even drier



Extended cool down

The automatic cooling down phase
which takes place before the end of a
programme can be extended for all
programmes with selectable drying
levels in 2 minute increments up to 18
minutes. This makes the garments
easier to handle.

Options



Factory default setting



= Cool down time 2 minutes

longer



= Cool down time 4 minutes

longer



= Cool down time 6 minutes

longer



= Cool down time 8 minutes

longer



= Cool down time 10 minutes

longer



= Cool down time 12 minutes

longer



= Cool down time 14 minutes

longer



= Cool down time 16 minutes

longer



= Cool down time 18 minutes

longer



Buzzer volume

The buzzer can be set so that it is
louder.



= quieter



Factory default setting

Summary of Contents for TCE 620 WP













































































Search results

Summary of Contents for TCE 620 WP

Reviews:

Related manuals for TCE 620 WP

Brands by name

Popular brands

Miele TCE 620 WP, Operating Instructions Manual

Search results

Summary of Contents for TCE 620 WP

Reviews:

Related manuals for TCE 620 WP

Brands by name

Popular brands