manualshive.com logo in svg

Miele PWM 508 Mop Star 80, Operating And Installation Instructions

Share
Download
Miele PWM 508 Mop Star 80 Operating And Installation Instructions Download Page 55

Problem solving guide

55

The door will not open

Problem

Possible cause and remedy

The door cannot be
pulled open during a
wash programme.

The door is locked during the washing process.

Touch the 

Start/Stop

 sensor.

Select 

Cancel programme

 or 

Add laundry

.

The door will unlock and you will be able to pull it
open.

The water level in the drum is too high.

Cancel the programme. The washing machine will
pump away the water.

 Programme cancelled

appears in the display
at the end of a
programme or after a
programme has been
cancelled.

For safety reasons, the door cannot be opened if the
suds temperature is higher than 55°C.

Wait until the temperature in the drum has
decreased and the message has gone out in the
display.

The following appears
in the display:

The door lock is jammed.

Call Miele.

The door lock has jammed.

Call Miele.

Summary of Contents for PWM 508 Mop Star 80





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands